This section contains the settings that you can view and configure for most of your tasks. The list of settings available depends on the task you are configuring.
Settings specified during task creation
You can specify the following settings when creating a task. Some of these settings can also be modified in the properties of the created task.
Client devices are not restarted automatically after the operation. To complete the operation, you must restart a device (for example, manually or through a device management task). Information about the required restart is saved in the task results and in the device status. This option is suitable for tasks on servers and other devices where continuous operation is critical.
Client devices are always restarted automatically if a restart is required for completion of the operation. This option is useful for tasks on devices that provide for regular pauses in their operation (shutdown or restart).
Running applications may prevent a restart of the client device. For example, if a document is being edited in a word processing application and is not saved, the application does not allow the device to restart.
If this option is enabled, such applications on a locked device are forced to close before the device restart. As a result, users may lose their unsaved changes.
If this option is disabled, a locked device is not restarted. The task status on this device states that a device restart is required. Users have to manually close all applications running on locked devices and restart these devices.
The task runs regularly, with the specified interval in days. Additionally, you can specify a date and time of the first task run. These additional options become available, if they are supported by the application for which you create the task.
By default, the task runs every day, starting from the current system date and time.
The task runs regularly, with the specified interval in days. This schedule does not support observance of daylight saving time (DST). It means that when clocks jump one hour forward or backward at the beginning or ending of DST, the actual task start time does not change.
We do not recommend that you use this schedule. It is needed for backward compatibility of Kaspersky Security Center Linux.
By default, the task starts every day at the current system time.
The current task starts after another task completes. You can select how the previous task must complete (successfully or with error) to trigger the start of the current task. This parameter only works if both tasks are assigned to the same devices.
This option determines the behavior of a task if a client device is not visible on the network when the task is about to start.
If this option is enabled, the system attempts to start the task the next time the Kaspersky application is run on the client device. If the task schedule is Manually, Once or Immediately, the task is started immediately after the device becomes visible on the network or immediately after the device is included in the task scope.
If this option is disabled, only scheduled tasks run on client devices. For Manually, Once and Immediately schedule, tasks run only on those client devices that are visible on the network. For example, you may want to disable this option for a resource-consuming task that you want to run only outside of business hours.
If this option is enabled, the task is started on client devices randomly within a specified time interval, that is, distributed task start. A distributed task start helps to avoid a large number of simultaneous requests by client devices to the Administration Server when a scheduled task is running.
The distributed start time is calculated automatically when a task is created, depending on the number of client devices to which the task is assigned. Later, the task is always started on the calculated start time. However, when task settings are edited or the task is started manually, the calculated value of the task start time changes.
If this option is disabled, the task starts on client devices according to the schedule.
If this option is enabled, the task is started on client devices randomly within the specified time interval. A distributed task start helps to avoid a large number of simultaneous requests by client devices to the Administration Server when a scheduled task is running.
If this option is disabled, the task starts on client devices according to the schedule.
By default, this option is disabled. The default time interval is one minute.
You can specify DNS names, IP addresses, and IP subnets of devices to which you want to assign the task.
You may want to use this option to execute a task for a specific subnet. For example, you may want to install a certain application on devices of accountants or to scan devices in a subnet that is probably infected.
The task is assigned to devices included in an administration group. You can specify one of the existing groups or create a new one.
For example, you may want to use this option to run a task of sending a message to users if the message is specific for devices included in a specific administration group.
If a task is assigned to an administration group, the Security tab is not display in the task properties window because group tasks are subject to the security settings of the groups to which they apply.
Fill in the Account and Password fields to specify the details of an account under which the task is run. The account must have sufficient rights for this task.
When this option is enabled, the task that is effective on the primary Administration Server is also applied on the secondary Administration Servers (including virtual ones). If a task of the same type already exists on the secondary Administration Server, both tasks are applied on the secondary Administration Server—the existing one and the one that is inherited from the primary Administration Server.
This option is only available when the Distribute to subgroups option is enabled.
The operating system on the device starts at the specified time before the task is started. The default time period is five minutes.
Enable this option if you want the task to run on all of the client devices from the task scope, including those devices that are turned off when the task is about to start.
If you want the device to be automatically turned off after the task is complete, enable the Shut down the devices after completing the task option. This option can be found in the same window.
For example, you may want to enable this option for an install update task that installs updates to client devices each Friday after business hours, and then turns off these devices for the weekend.
Application events related to execution of the task on all client devices from the task scope are stored on the Administration Server during the specified number of days. When this period elapses, the information is deleted from the Administration Server.
Application events related to execution of the task on all client devices from the task scope are stored centrally in the Syslog Event Log of the Administration Server operating system (OS).
You can select the methods by which administrators receive notifications about task execution results: by email, by SMS, and by running an executable file. To configure notification, click the Settings link.
By default, all notification methods are disabled.
If the scope of a task is determined by an administration group, you can view this group. No changes are available here. However, you can set Exclusions from task scope.
If the scope of a task is determined by a list of devices, you can modify this list by adding and removing devices.
You can specify groups of devices to which the task is not applied. Groups to be excluded can only be subgroups of the administration group to which the task is applied.