The table describes all available values and the default values of all the settings that you can specify for the Anti-Cryptor task.
|
|
|
Setting
|
Description
|
Values
|
UseHostBlocker
|
Enables or disables blocking of untrusted computers.
If blocking of untrusted computers is disabled, the application still scans remote computers actions on network file resources for malicious encryption, when the Anti-Cryptor task is running. If malicious activity is detected, the EncryptionDetected event is created, but the attacking computer is not blocked.
|
Yes—Enable blocking of untrusted computers.
No (default value) — Disable blocking of untrusted computers.
|
BlockTime
|
Specifies the amount of time an untrusted computer is blocked (in minutes).
If a compromised computer is blocked, and you change the value of the BlockTime setting, the blocking time for this computer will not change. The blocking time is not a dynamic value, and is calculated at the moment of blocking.
|
Integer from 1 to 4294967295.
The default value is 30.
|
UseExcludeMasks
|
Enables or disables exclusion of objects specified by the ExcludeMasks setting from the scan scope.
This setting only applies if the ExcludeMasks setting is specified.
|
Yes — Exclude objects specified by the ExcludeMasks setting from the protection scope
No (default value) — Do not exclude objects specified by the ExcludeMasks setting from the protection scope.
|
ExcludeMasks
|
Excludes objects from the protection scope by names or masks. You can use this setting to exclude an individual file from the specified protection scope by name or exclude multiple files at the same time using masks in the shell format.
Before specifying a value for this setting, make sure that the UseExcludeMasks setting is enabled.
If you want to specify several masks, specify each mask on a new line with a new index (ExcludeMasks.item_0000, ExcludeMasks.item_0001).
|
The default value is not defined.
|
The [ScanScope.item_#] section contains the scopes protected by the application. For the Anti-Cryptor task, you need to specify at least one protection scope; you can only specify shared directories.
You can define several [ScanScope.item_#] sections in any order in the configuration file. The application will process the scopes by index in ascending order.
Each [ScanScope.item_#] section contains the following settings:
|
AreaDesc
|
Description of protection scope; contains additional information about the protection scope.
|
Default value: All shared directories.
|
UseScanArea
|
Enables protection of the specified scope. To run the task, enable protection of at least one scope.
|
Yes (default value) — Protect the specified scope.
No — Do not protect the specified scope.
|
AreaMask
|
Protection scope limitation. Within the protection scope, the application protects only the files that are specified using the masks in the shell format.
You can specify several AreaMask.item_# items in any order. The application will process the scopes by index in ascending order.
|
Default value: * (protect all objects)
|
Path
|
Path to the directory with the objects to be protected.
|
<path to local directory> – Protect a local directory accessible via SMB/NFS. You can use masks to specify the path.
You can use the * (asterisk) character to create a file or directory name mask.
You can indicate a single * character to represent any set of characters (including an empty set) preceding the / character in the file or directory name. For example, /dir/*/file or /dir/*/*/file.
You can indicate two consecutive * characters to represent any set of characters (including an empty set and the / character) in the file or directory name. For example, /dir/**/file*/ or /dir/file**/.
The ** mask can be used only once in a directory name. For example, /dir/**/**/file is an incorrect mask.
You can use a single ? character to represent any one character in the file or directory name.
AllShared (default value) — Protect all resources accessible via SMB/NFS.
Shared:SMB <path> — Protect resources accessible via SMB.
Shared:NFS <path> — Protect resources accessible via NFS.
|
The [ExcludedFromScanScope.item_#] section contains the objects to be excluded from all [ScanScope.item_#] sections. The objects that match the rules of any [ExcludedFromScanScope.item_#] section are not scanned. The format of the [ExcludedFromScanScope.item_#] section is similar to the format of the [ScanScope.item_#] section. You can define several [ExcludedFromScanScope.item_#] sections in any order in the configuration file. The application will process the scopes by index in ascending order.
Each [ExcludedFromScanScope.item_#] section contains the following settings:
|
AreaDesc
|
Description of the protection exclusion scope, which contains additional information about the exclusion scope.
|
Default value: All objects.
|
UseScanArea
|
Excludes the specified scope from protection.
|
Yes (default value) — Exclude the specified scope from protection.
No — Do not exclude the specified scope from protection.
|
AreaMask
|
Limitation of the protection exclusion scope. In the exclusion scope, the application excludes only the objects that are specified using masks in the shell format.
You can specify several AreaMask.item_# items in any order. The application will process the scopes by index in ascending order.
|
Default value: * (exclude all objects).
|
Path
|
Path to the directory with objects excluded from protection.
|
<path to local directory> — Exclude objects in the specified directory from protection. You can use masks to specify the path.
You can use the * (asterisk) character to create a file or directory name mask.
You can indicate a single * character to represent any set of characters (including an empty set) preceding the / character in the file or directory name. For example, /dir/*/file or /dir/*/*/file.
You can indicate two consecutive * characters to represent any set of characters (including an empty set and the / character) in the file or directory name. For example, /dir/**/file*/ or /dir/file**/.
The ** mask can be used only once in a directory name. For example, /dir/**/**/file is an incorrect mask.
To exclude the mount point /dir, you need to specifically indicate /dir (no asterisk).
The mask /dir/* excludes all mount points at the level below /dir but not /dir itself. The /dir/** mask excludes all mount points below the level of /dir but not /dir itself.
You can use a single ? character to represent any one character in the file or directory name.
Mounted:NFS – Exclude the remote directories mounted on a computer using the NFS protocol from protection.
Mounted:SMB – Exclude the remote directories mounted on a computer using the Samba protocol from protection.
AllRemoteMounted – Exclude all remote directories mounted on the computer using the Samba and NFS protocols from protection.
|