Creating a set of resources for an agent

In the KUMA web interface, an agent service is created based on the set of resources for an agent that unites connectors and destinations.

To create a set of resources for an agent in the KUMA web interface:

1. In the KUMA web interface, under Resources → Agents, click Add agent.

   This opens a window for creating an agent with the Base settings tab active.

2. Specify the settings on the Base settings tab:
   • In the Agent name field, enter a unique name for the created service. The name must contain 1 to 128 Unicode characters.
   • In the Tenant drop-down list, select the tenant that will own the storage.
   • If necessary, move the Debug toggle switch to the active position to enable logging of service operations.
   • You can optionally add up to 256 Unicode characters describing the service in the Description field.
3. Click to create a connection for the agent and switch to the added Connection <number> tab.

   You can remove tabs by clicking .

4. In the Connector group of settings, add a connector:
   • If you want to select an existing connector, select it from the drop-down list.
   • If you want to create a new connector, select Create new in the drop-down list and specify the following settings:
     • Specify the connector name in the Name field. The name must contain 1 to 128 Unicode characters.
     • In the Type drop-down list, select the connector type and specify its settings on the Basic settings and Advanced settings tabs. The available settings depend on the selected type of connector:
       • tcp
       • udp
       • nats-jetstream
       • kafka
       • http
       • file
       • ftp
       • nfs
       • wmi
       • wec
       • snmp

       The agent type is determined by the connector that is used in the agent. The only exception is for agents with a destination of the diode type. These agents are considered to be diode agents.

       When using the tcp or udp connector type at the normalization stage, IP addresses of the assets from which the events were received will be written in the DeviceAddress event field if it is empty.

       The ability to edit previously created wec or wmi connections in agents, collectors, and connectors is limited. You can change the connection type from wec to wmi and vice versa, but you cannot change the wec or wmi connection to any other connection type. At the same time, when editing other connection types, you cannot select the wec or wmi types. You can create connections without any restrictions on the types of connectors.

   • You can optionally add up to 4,000 Unicode characters describing the resource in the Description field.

   The connector is added to the selected connection of the agent's set of resources. The created connector is only available in this resource set and is not displayed in the web interface Resources → Connectors section.

5. In the Destinations group of settings, add a destination.
   • If you want to select an existing destination, select it from the drop-down list.
   • If you want to create a new destination, select Create new in the drop-down list and specify the following settings:
     • Specify the destination name in the Name field. The name must contain 1 to 128 Unicode characters.
     • In the Type drop-down list, select the destination type and specify its settings on the Basic settings and Advanced settings tabs. The available settings depend on the selected type of destination:
       • nats-jetstream—used for NATS communications.
       • tcp—used for communications over TCP.
       • http—used for HTTP communications.
       • diode—used to transmit events using a data diode.
       • kafka—used for Kafka communications.
       • file—used for writing to a file.
   • You can optionally add up to 4,000 Unicode characters describing the resource in the Description field.

     The advanced settings for an agent destination (such as TLS mode and compression) must match the advanced destination settings for the collector that you want to link to the agent.

   There can be more than one destination point. You can add them by clicking the Add destination button and can remove them by clicking the button.

6. Repeat steps 3–5 for each agent connection that you want to create.
7. Click Save.

The set of resources for the agent is created and displayed under Resources → Agents. Now you can create an agent service in KUMA.