Compatibility of Kaspersky Endpoint Agent with other programs

Kaspersky Anti Targeted Attack Platform does not support joint operation with programs not listed in this section.

Compatibility of Endpoint Sensors 3.5 with Kaspersky programs

You can use Kaspersky Endpoint Security for Windows version 10 SP2 MR3 or 11.0 and the standalone Endpoint Sensors program version 3.5 on the same computer. To do so:

  1. Disable Endpoint Sensors in the KES program.

    For details on how to disable Endpoint Sensors in the KES program, refer to the Kaspersky Endpoint Security Help.

  2. Install the standalone Endpoint Sensors program version 3.5 on all the computers of your organization's local area network on which you want to use Endpoint Sensors.

Compatibility of Endpoint Sensors 3.6 with Kaspersky Endpoint Security for Windows

Information about the compatibility of Endpoint Sensors 3.6 with Kaspersky Endpoint Security for Windows (hereinafter also referred to as "KES") is listed in the following table.

Kaspersky Endpoint Security version 11.1.1 is compatible only with the Endpoint Sensors program that is part of KES. You cannot install KES 11.1.1 and the standalone Endpoint Sensors program on the same computer.

Compatibility of Endpoint Sensors with KES.

Version of the Kaspersky program

Compatibility mode

Installing the standalone Endpoint Sensors program after installing the other program

Installing the other program after installing the standalone Endpoint Sensors program

Supported operating systems

  • KES10 SP1 MR3 (Endpoint Sensors as part of KES version 1.0)
  • KES10 SP1 MR4 (Endpoint Sensors as part of KES version 1.0)

Joint operation.

Using Endpoint Sensors as part of KES is not supported.

Standard installation procedure.

KES when installed over the stand-alone Endpoint Sensors program does not remove the stand-alone Endpoint Sensors program.

  • Windows 7 SP1 Enterprise x86 x64
  • Windows 8.1.1 Enterprise x86 x64.
  • Windows 10 RS3 Enterprise x86 x64
  • Windows 10 RS4 Enterprise x86 x64
  • Windows 10 RS5 Enterprise x86 x64
  • Windows 10 RS6 Enterprise x86 x64
  • Windows Server 2008 R2 Enterprise x64.
  • Windows Server 2012 Standard x64.
  • Windows Server 2012 R2 Standard x64.
  • Windows Server 2016 Standard x64.
  • KES 10 SP2 (Endpoint Sensors as part of KES version 2.0)
  • KES 10 SP2 MR1 (Endpoint Sensors as part of KES version 2.0)
  • KES 10 SP2 MR2 (Endpoint Sensors as part of KES version 2.0)

Joint operation.

Using Endpoint Sensors as part of KES is not supported.

Standard installation procedure.

KES when installed over the stand-alone Endpoint Sensors program does not remove the stand-alone Endpoint Sensors program.

  • KES 10 SP2 MR3 (Endpoint Sensors as part of KES version 2.0)

Joint operation.

Using Endpoint Sensors as part of KES is supported.

Standard installation procedure.

KES when installed over the stand-alone Endpoint Sensors program does not remove the stand-alone Endpoint Sensors program.

  • KES 11.0.0 (Endpoint Sensors as part of KES version 3.0)

Joint operation.

Using Endpoint Sensors as part of KES is not supported.

To install the standalone Endpoint Sensors program, the Endpoint Sensors built into the KES program must be disabled.

For details on how to disable Endpoint Sensors in the KES program, refer to the Kaspersky Endpoint Security Help.

If the program is not disabled, installation fails with an error.

KES when installed over the stand-alone Endpoint Sensors program does not remove the stand-alone Endpoint Sensors program regardless of whether an Endpoint Sensors program is included with the KES program.

  • KES 11.0.1 (Endpoint Sensors as part of KES version 3.0)

Joint operation.

Using Endpoint Sensors as part of KES is supported.

To install the standalone Endpoint Sensors program, the Endpoint Sensors built into the KES program must be disabled.

For details on how to disable Endpoint Sensors in the KES program, refer to the Kaspersky Endpoint Security Help.

If the program is not disabled, installation fails with an error.

KES when installed over the stand-alone Endpoint Sensors program does not remove the stand-alone Endpoint Sensors program regardless of whether an Endpoint Sensors program is included with the KES program.

  • KES 11.1 (Endpoint Sensors as part of KES version 3.5)

Joint operation is not supported.

Only the built-in Endpoint Sensors program as part of KES can be used.

A stand-alone Endpoint Sensors program cannot be installed over KES.

You can enable the built-in Endpoint Sensors program as part of the KES program.

KES removes the standalone Endpoint Sensors program.

Settings of the stand-alone Endpoint Sensors program are not preserved.

Compatibility of Endpoint Sensors version 3.6 with Kaspersky Security for Windows Server version 10.1.2 (KSWS 10.1.2)

Installing the Endpoint Sensors program version 3.6.0.62 on the same server as the KSWS application version 10.1.2 is supported for the following operating system:

Compatibility of Endpoint Sensors version 3.6 with Kaspersky Security for Virtualization 5.1 Light Agent (KSV LA)

Installing Endpoint Sensors on the same virtual machine as the KSV LA program is supported for the following operating systems:

To use Endpoint Sensors with KSV LA in the virtual infrastructure, one of the following hypervisors must be installed (depending on the virtualization platform):

Cloning virtual machines with installed Endpoint Sensors and KSV LA is not supported. Clone the virtual machine, generate a new SMBIOS GUID for it, then install the Endpoint Sensors program.

Compatibility of Kaspersky Endpoint Agent 3.8 with Kaspersky Security for Virtualization Light Agent (KSV LA)

Kaspersky Endpoint Agent 3.8 is compatible with Kaspersky Security for Virtualization Light Agent (KSV LA) versions 5.1, 5.1.1, 5.1.2, 5.1.3.

Compatibility of Kaspersky Endpoint Agent versions 3.8 and 3.9 with Kaspersky Endpoint Protection Platform programs

Kaspersky Endpoint Agent versions 3.8 and 3.9 are compatible with the following Endpoint Protection Platform programs:

If Endpoint Sensor version 3.6.X is installed and used on the device as part of Kaspersky Endpoint Security, it is recommended to disable Endpoint Sensor before installing Kaspersky Endpoint Agent 3.8 and 3.9 to avoid possible conflicts between the programs.

Compatibility of Kaspersky Endpoint Agent program versions 3.8 and 3.9 with other Kaspersky programs

Kaspersky Endpoint Agent program versions 3.8 and 3.9 are compatible with the following Kaspersky programs and solutions:

Compatibility of the Kaspersky Endpoint Agent program with third-party antivirus programs

One of the following third-party anti-virus programs can be installed on computers on which you want to install Kaspersky Endpoint Agent (Endpoint Sensors):

If you install more than one third-party anti-virus program, correct operation of Kaspersky Endpoint Agent (Endpoint Sensors) is not guaranteed.

If RealTimes Desktop Service is installed on computers on which the Endpoint Sensors component will be installed, you are advised to uninstall it before installing Endpoint Sensors.

Page top